GE Profile OVEN TOO HOT FOR SENSOR COOKING: the cavity must cool first
On the PVM9179 convection hood combination a bake, roast or air fry cycle leaves the cavity hotter than the humidity sensor can work with.
Mon–Sat, 8am–8pm
- Sensors and temperature
- Microwave control board and touchpad repair
- Source: GE Profile
Book a visit
Three short steps, about a minute.
or call (844) 393-5858
Loading appointment form…
The appointment form couldn’t load. Please try again.
What OVEN TOO HOT
actually means.
On the PVM9179 convection hood combination a bake, roast or air fry cycle leaves the cavity hotter than the humidity sensor can work with. Pressing a sensor key in that state brings up the message, and the microwave switches to cooking by time or waits until the cavity cools.
GE Profile microwave display · also shown as OVEN TOO HOT FOR SENSOR COOKING—USING ALTERNATE METHOD
What to do when OVEN TOO HOT shows on the microwaveKind of codeSensors and temperature
The control has stopped trusting what one of its sensors reports: the cook or humidity sensor that ends a sensor reheat when steam rises, or a thermal cutout that trips when the cavity or the magnetron runs too hot. A cutout that opens stops the microwave mid-cycle and often recovers once it cools; one that keeps tripping, or a sensor program that shuts off at once every time, needs the sensor, its wiring or the airflow behind it checked.
Usually leads toMicrowave control board and touchpad repair
Tracing a dead display, keys that do not answer or a code that keeps returning to the keypad, the ribbon, the relays or the main board, and replacing only the part that failed.
Shows up asWhat a Microwave Error Code Is Telling You
A microwave error code may be a letter and a number on the display, a lock or demo word, a row of dashes, or a beep with a blinking clock, and it can show while the microwave still heats or block every key until it is cleared.
MakeGE Profile
GE Profile microwaves repaired where they hang or sit, whether it is the vent fan, the cavity lamp, the keypad or the heat that gave out.
SourceGE Profile PVM9179 convection microwave hood combination owner's manual
Printed in the PVM9179 manual. The display text runs on as OVEN TOO HOT FOR SENSOR COOKING, USING ALTERNATE METHOD.
Before you book,
in this order.
Each step comes from GE Profile's own guidance for OVEN TOO HOT on its microwaves. Follow it to the end: the last card says whether this is a visit.
Follow the prompt on the display to cook by time.
Or leave the door open for a few minutes and try the sensor program again once the cavity has cooled.
If the message appears with a cold cavity, book a visit so the temperature sensor and control can be checked.
Still there?
It usually turns into microwave control board and touchpad repair. Book with the code and the model number.
What not to do
The message is not a sensor failure; it is the control protecting its sensor programs. It becomes a repair question only when it shows on a microwave that has not baked or air fried recently.
What you may
notice with it.
The microwave problems OVEN TOO HOT tends to arrive with. Answer these at the microwave before anyone is booked.
All problems
Where OVEN TOO HOT usually leads
Microwave control board and touchpad repair.
GE Profile
microwaves.
GE Profile microwaves repaired where they hang or sit, whether it is the vent fan, the cavity lamp, the keypad or the heat that gave out.
GE Profile microwave repairMore GE Profile codes
Sensors and temperature on other makes
Microwave hood combination
The microwave that hangs from the wall cabinets above the burners, heating food in its cavity while its own fan, light and filters handle the steam and grease rising from the pans beneath it.
Built-in microwave
A microwave set into a tall cabinet or a wall of cabinetry at eye level, either a countertop body wrapped in a trim kit or a true built-in model, including speed and convection microwaves that brown as well as heat.
Microwave drawer
A microwave built under a counter or into a kitchen island that opens like a drawer at the touch of a key, with a motor and gears sliding its cavity out toward you.
In GE Profile's own words
One of the sensor cooking
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Printed in the PVM9179 manual. The display text runs on as OVEN TOO HOT FOR SENSOR COOKING, USING ALTERNATE METHOD.
GE Profile OVEN TOO HOT microwave repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about OVEN TOO HOT.
Can I clear OVEN TOO HOT myself?
Why can't I use sensor reheat right after air frying in my GE Profile?
Does this message mean my GE Profile PVM9179 is overheating?
Should I worry if the message appears on a cold GE Profile microwave?
Back to your everyday
Still showing OVEN TOO HOT?
Three details make the booking useful: the characters or beeps just as they appeared, every character of the model number, and whether a cup of water still warms up. With those, the technician arrives already halfway to the answer.