Thermador ENJOY YOUR MICROWAVE: the MicroDrawer restarted after a power cut
The MicroDrawer uses its first-start greeting as its power-outage notice too.
Mon–Sat, 8am–8pm
- Power and supply
- Microwave diagnostic visit
- Source: Thermador
Book a visit
Three short steps, about a minute.
or call (844) 393-5858
Loading appointment form…
The appointment form couldn’t load. Please try again.
What ENJOY YOUR MICROWAVE TOUCH CLEAR
actually means.
The MicroDrawer uses its first-start greeting as its power-outage notice too. It flashes on and off after the supply returns, and by then the clock, any program that was running and the current settings have been wiped.
Thermador microwave display · also shown as ENJOY YOUR MICRO- WAVE TOUCH CLEAR
What to do when ENJOY YOUR MICROWAVE TOUCH CLEAR shows on the microwaveKind of codePower and supply
The microwave has noticed trouble with the power reaching it: an outage or a brownout that interrupted a cycle, a voltage too low for the magnetron to start, or a supply that dipped when something else on the circuit switched on. As often as not the cause is the circuit, the outlet in the cabinet above or the breaker rather than the unit; a main fuse that blows again after a reset points inside, where only a technician goes.
Usually leads toMicrowave diagnostic visit
A visit that times a cup of water against the clock, checks the door and its switches, then tests the high-voltage section, the controls and the moving parts one at a time until a single part is named.
Shows up asWhat a Microwave Error Code Is Telling You
A microwave error code may be a letter and a number on the display, a lock or demo word, a row of dashes, or a beep with a blinking clock, and it can show while the microwave still heats or block every key until it is cleared.
MakeThermador
Thermador microwaves diagnosed in place, from a drawer that will not glide open to a built-in unit that runs with no heat.
SourceThermador MD24BS / MD30BS MicroDrawer Use and Care Guide
Thermador MicroDrawer MD24BS and MD30BS (Use and Care Guide 8001299202). Thermador's troubleshooting table lists a flashing display after a power failure.
Before you book,
in this order.
Each step comes from Thermador's own guidance for ENJOY YOUR MICROWAVE TOUCH CLEAR on its microwaves. Follow it to the end: the last card says whether this is a visit.
Touch Stop/Clear to stop the message.
Set the clock and restart the food if it was cooking; check food safety if it sat for a long time.
If the greeting returns without any outage in the home, have the circuit checked, then book a visit if the circuit is fine.
Still there?
It usually turns into microwave diagnostic visit. Book with the code and the model number.
What not to do
The greeting is not an error code and nothing has failed because of it. A breaker that trips each time the drawer starts is a separate, urgent symptom.
What you may
notice with it.
The microwave problems ENJOY YOUR MICROWAVE TOUCH CLEAR tends to arrive with. Answer these at the microwave before anyone is booked.
All problems
Where ENJOY YOUR MICROWAVE TOUCH CLEAR usually leads
Microwave diagnostic visit.
Thermador
microwaves.
Thermador microwaves diagnosed in place, from a drawer that will not glide open to a built-in unit that runs with no heat.
Thermador microwave repairMore Thermador codes
Power and supply on other makes
Microwave hood combination
The microwave that hangs from the wall cabinets above the burners, heating food in its cavity while its own fan, light and filters handle the steam and grease rising from the pans beneath it.
Built-in microwave
A microwave set into a tall cabinet or a wall of cabinetry at eye level, either a countertop body wrapped in a trim kit or a true built-in model, including speed and convection microwaves that brown as well as heat.
Microwave drawer
A microwave built under a counter or into a kitchen island that opens like a drawer at the touch of a key, with a motor and gears sliding its cavity out toward you.
In Thermador's own words
If this occurs, the current settings will be erased.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Thermador MicroDrawer MD24BS and MD30BS (Use and Care Guide 8001299202). Thermador's troubleshooting table lists a flashing display after a power failure.
Thermador ENJOY YOUR MICROWAVE TOUCH CLEAR microwave repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about ENJOY YOUR MICROWAVE TOUCH CLEAR.
Can I clear ENJOY YOUR MICROWAVE TOUCH CLEAR myself?
Why is my Thermador MicroDrawer flashing a greeting?
Was my food cooked if the Thermador drawer lost power mid-cycle?
Does the Thermador greeting mean the board reset itself because of a failure?
Back to your everyday
Still showing ENJOY YOUR MICROWAVE TOUCH CLEAR?
Three details make the booking useful: the characters or beeps just as they appeared, every character of the model number, and whether a cup of water still warms up. With those, the technician arrives already halfway to the answer.