JennAir F8E5: the exhaust air temperature sensor
JennAir hood combinations read the temperature of the exhaust air to manage the fan and protect the unit from heat below.
Mon–Sat, 8am–8pm
- Sensors and temperature
- Microwave control board and touchpad repair
- Source: JennAir
Book a visit
Three short steps, about a minute.
or call (844) 393-5858
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F8E5
actually means.
JennAir hood combinations read the temperature of the exhaust air to manage the fan and protect the unit from heat below. F8E5 appears when that exhaust air temperature sensor, or its wiring, returns a reading the control rejects, and the function that was running stops.
JennAir microwave display · also shown as F8 E5
What to do when F8E5 shows on the microwaveKind of codeSensors and temperature
The control has stopped trusting what one of its sensors reports: the cook or humidity sensor that ends a sensor reheat when steam rises, or a thermal cutout that trips when the cavity or the magnetron runs too hot. A cutout that opens stops the microwave mid-cycle and often recovers once it cools; one that keeps tripping, or a sensor program that shuts off at once every time, needs the sensor, its wiring or the airflow behind it checked.
Usually leads toMicrowave control board and touchpad repair
Tracing a dead display, keys that do not answer or a code that keeps returning to the keypad, the ribbon, the relays or the main board, and replacing only the part that failed.
Shows up asWhat a Microwave Error Code Is Telling You
A microwave error code may be a letter and a number on the display, a lock or demo word, a row of dashes, or a beep with a blinking clock, and it can show while the microwave still heats or block every key until it is cleared.
MakeJennAir
JennAir microwaves looked at in place, with the breaker, the door switches and a one-minute heat test covered before any part is priced.
SourceJennAir Product Help, over-the-range microwave: F8E5
From JennAir's help pages for its microwave hood combinations (Euro-style, including the convection models). The code set varies with the control generation, so a code missing from your model's manual may not apply to it.
Before you book,
in this order.
Each step comes from JennAir's own guidance for F8E5 on its microwaves. Follow it to the end: the last card says whether this is a visit.
Turn the microwave off at the circuit breaker, count a full minute, then restore power.
Give it a minute on standby; a code that does not reappear was likely a one-time glitch, so run a short cycle to confirm.
Make sure the grease filters are in place and clean, since they change the airflow over the sensor.
Book a visit if F8E5 returns.
Still there?
It usually turns into microwave control board and touchpad repair. Book with the code and the model number.
What not to do
F8E5 is a sensor code, while a blocked vent door is F7 E9. The code does not mean the burners or elements below are overheating on their own.
What you may
notice with it.
The microwave problems F8E5 tends to arrive with. Answer these at the microwave before anyone is booked.
All problems
Where F8E5 usually leads
Microwave control board and touchpad repair.
JennAir
microwaves.
JennAir microwaves looked at in place, with the breaker, the door switches and a one-minute heat test covered before any part is priced.
JennAir microwave repairMore JennAir codes
All 21 JennAir codesSensors and temperature on other makes
Microwave hood combination
The microwave that hangs from the wall cabinets above the burners, heating food in its cavity while its own fan, light and filters handle the steam and grease rising from the pans beneath it.
Built-in microwave
A microwave set into a tall cabinet or a wall of cabinetry at eye level, either a countertop body wrapped in a trim kit or a true built-in model, including speed and convection microwaves that brown as well as heat.
Microwave drawer
A microwave built under a counter or into a kitchen island that opens like a drawer at the touch of a key, with a motor and gears sliding its cavity out toward you.
In JennAir's own words
There may a problem with the Exhaust Air Temperature Sensor, or the associated wiring.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. From JennAir's help pages for its microwave hood combinations (Euro-style, including the convection models). The code set varies with the control generation, so a code missing from your model's manual may not apply to it.
JennAir F8E5 microwave repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F8E5.
Can I clear F8E5 myself?
Why does my JennAir fan act oddly with F8E5?
Could greasy filters cause F8E5 on a JennAir?
Is F8E5 on JennAir urgent?
Back to your everyday
Still showing F8E5?
Three details make the booking useful: the characters or beeps just as they appeared, every character of the model number, and whether a cup of water still warms up. With those, the technician arrives already halfway to the answer.