JennAir F3T3: the temperature sensor in the vent section
A JennAir hood combination keeps watch on the heat coming up from the cooking surface below with its own thermistor.
Mon–Sat, 8am–8pm
- Sensors and temperature
- Microwave control board and touchpad repair
- Source: JennAir
Book a visit
Three short steps, about a minute.
or call (844) 393-5858
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F3T3
actually means.
A JennAir hood combination keeps watch on the heat coming up from the cooking surface below with its own thermistor. F3T3 means that sensor or its wiring is out of range, so the automatic fan response to rising heat cannot be trusted.
JennAir microwave display · also shown as F3 T3
What to do when F3T3 shows on the microwaveKind of codeSensors and temperature
The control has stopped trusting what one of its sensors reports: the cook or humidity sensor that ends a sensor reheat when steam rises, or a thermal cutout that trips when the cavity or the magnetron runs too hot. A cutout that opens stops the microwave mid-cycle and often recovers once it cools; one that keeps tripping, or a sensor program that shuts off at once every time, needs the sensor, its wiring or the airflow behind it checked.
Usually leads toMicrowave control board and touchpad repair
Tracing a dead display, keys that do not answer or a code that keeps returning to the keypad, the ribbon, the relays or the main board, and replacing only the part that failed.
Shows up asWhat a Microwave Error Code Is Telling You
A microwave error code may be a letter and a number on the display, a lock or demo word, a row of dashes, or a beep with a blinking clock, and it can show while the microwave still heats or block every key until it is cleared.
MakeJennAir
JennAir microwaves looked at in place, with the breaker, the door switches and a one-minute heat test covered before any part is priced.
SourceJennAir Product Help, over-the-range microwave: F3T3
From JennAir's help pages for its microwave hood combinations (Euro-style, including the convection models). The code set varies with the control generation, so a code missing from your model's manual may not apply to it.
Before you book,
in this order.
Each step comes from JennAir's own guidance for F3T3 on its microwaves. Follow it to the end: the last card says whether this is a visit.
Turn the microwave off at the circuit breaker, count a full minute, then restore power.
Give it a minute on standby; a code that does not reappear was likely a one-time glitch, so run a short cycle to confirm.
Run the vent fan manually while you cook below until the repair.
If F3T3 comes back, book a visit to test the thermistor.
Still there?
It usually turns into microwave control board and touchpad repair. Book with the code and the model number.
What not to do
F3T3 does not mean the vent fan motor has failed. It also has nothing to do with the magnetron or the door switches.
What you may
notice with it.
The microwave problems F3T3 tends to arrive with. Answer these at the microwave before anyone is booked.
All problems
Where F3T3 usually leads
Microwave control board and touchpad repair.
JennAir
microwaves.
JennAir microwaves looked at in place, with the breaker, the door switches and a one-minute heat test covered before any part is priced.
JennAir microwave repairMore JennAir codes
All 21 JennAir codesSensors and temperature on other makes
Microwave hood combination
The microwave that hangs from the wall cabinets above the burners, heating food in its cavity while its own fan, light and filters handle the steam and grease rising from the pans beneath it.
Built-in microwave
A microwave set into a tall cabinet or a wall of cabinetry at eye level, either a countertop body wrapped in a trim kit or a true built-in model, including speed and convection microwaves that brown as well as heat.
Microwave drawer
A microwave built under a counter or into a kitchen island that opens like a drawer at the touch of a key, with a motor and gears sliding its cavity out toward you.
In JennAir's own words
There may be a problem with the Hood Temperature Thermistor or the associated wiring.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. From JennAir's help pages for its microwave hood combinations (Euro-style, including the convection models). The code set varies with the control generation, so a code missing from your model's manual may not apply to it.
JennAir F3T3 microwave repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F3T3.
Can I clear F3T3 myself?
Why does my JennAir fan no longer come on by itself?
Can I cook below a JennAir showing F3T3?
Is F3T3 on JennAir an expensive repair?
Back to your everyday
Still showing F3T3?
Three details make the booking useful: the characters or beeps just as they appeared, every character of the model number, and whether a cup of water still warms up. With those, the technician arrives already halfway to the answer.