JennAir F6E0: the main control could not carry out a function
JennAir's help page describes F6E0 as the microwave being unable to execute a function, with the appliance control board or its wiring named as the likely source.
Mon–Sat, 8am–8pm
- Control board and touchpad
- Microwave control board and touchpad repair
- Source: JennAir
Book a visit
Three short steps, about a minute.
or call (844) 393-5858
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F6E0
actually means.
JennAir's help page describes F6E0 as the microwave being unable to execute a function, with the appliance control board or its wiring named as the likely source. It is the board telling you it has lost track of its own job.
JennAir microwave display · also shown as F6 E0
What to do when F6E0 shows on the microwaveKind of codeControl board and touchpad
The electronics that read the keys and run the cycle have flagged a problem with themselves: a key that the control sees as held down for too long, a membrane keypad worn through or swollen by steam, a lost link between the keypad and the board, or a board that failed its own check after a surge. A breaker reset now and then clears a glitch; a stuck key or a code that comes straight back points to the keypad or the board.
Usually leads toMicrowave control board and touchpad repair
Tracing a dead display, keys that do not answer or a code that keeps returning to the keypad, the ribbon, the relays or the main board, and replacing only the part that failed.
Shows up asWhat a Microwave Error Code Is Telling You
A microwave error code may be a letter and a number on the display, a lock or demo word, a row of dashes, or a beep with a blinking clock, and it can show while the microwave still heats or block every key until it is cleared.
MakeJennAir
JennAir microwaves looked at in place, with the breaker, the door switches and a one-minute heat test covered before any part is priced.
SourceJennAir Product Help, over-the-range microwave: F6E0
From JennAir's help pages for its microwave hood combinations (Euro-style, including the convection models). The code set varies with the control generation, so a code missing from your model's manual may not apply to it.
Before you book,
in this order.
Each step comes from JennAir's own guidance for F6E0 on its microwaves. Follow it to the end: the last card says whether this is a visit.
Turn the microwave off at the circuit breaker, count a full minute, then restore power.
Give it a minute on standby; a code that does not reappear was likely a one-time glitch, so run a short cycle to confirm.
Note what you were doing when the code appeared; it helps the technician narrow it down.
If F6E0 returns, book a visit to test the board and its connections.
Still there?
It usually turns into microwave control board and touchpad repair. Book with the code and the model number.
What not to do
F6E0 does not by itself point at the keypad, which has its own codes. It also does not mean the vent is blocked, which is F7E9.
What you may
notice with it.
The microwave problems F6E0 tends to arrive with. Answer these at the microwave before anyone is booked.
All problems
Where F6E0 usually leads
Microwave control board and touchpad repair.
JennAir
microwaves.
JennAir microwaves looked at in place, with the breaker, the door switches and a one-minute heat test covered before any part is priced.
JennAir microwave repairMore JennAir codes
All 21 JennAir codesControl board and touchpad on other makes
Microwave hood combination
The microwave that hangs from the wall cabinets above the burners, heating food in its cavity while its own fan, light and filters handle the steam and grease rising from the pans beneath it.
Built-in microwave
A microwave set into a tall cabinet or a wall of cabinetry at eye level, either a countertop body wrapped in a trim kit or a true built-in model, including speed and convection microwaves that brown as well as heat.
Microwave drawer
A microwave built under a counter or into a kitchen island that opens like a drawer at the touch of a key, with a motor and gears sliding its cavity out toward you.
In JennAir's own words
There may a problem with the Appliance Control Board, or the associated wiring.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. From JennAir's help pages for its microwave hood combinations (Euro-style, including the convection models). The code set varies with the control generation, so a code missing from your model's manual may not apply to it.
JennAir F6E0 microwave repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F6E0.
Can I clear F6E0 myself?
Is F6E0 on a JennAir always a bad board?
Can a power surge cause F6E0 on a JennAir?
How long does a JennAir board take to arrive?
Back to your everyday
Still showing F6E0?
Three details make the booking useful: the characters or beeps just as they appeared, every character of the model number, and whether a cup of water still warms up. With those, the technician arrives already halfway to the answer.