JennAir F2: the keypad flagged itself to the control
JennAir's hood combinations carry a separate touch keypad wired to the main control.
Mon–Sat, 8am–8pm
- Control board and touchpad
- Microwave control board and touchpad repair
- Source: JennAir
Book a visit
Three short steps, about a minute.
or call (844) 393-5858
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F2
actually means.
JennAir's hood combinations carry a separate touch keypad wired to the main control. F2 comes up when that keypad reports trouble, which usually traces back to moisture behind the membrane, a key worn through or a loose ribbon connection.
JennAir microwave display · also shown as F 2
What to do when F2 shows on the microwaveKind of codeControl board and touchpad
The electronics that read the keys and run the cycle have flagged a problem with themselves: a key that the control sees as held down for too long, a membrane keypad worn through or swollen by steam, a lost link between the keypad and the board, or a board that failed its own check after a surge. A breaker reset now and then clears a glitch; a stuck key or a code that comes straight back points to the keypad or the board.
Usually leads toMicrowave control board and touchpad repair
Tracing a dead display, keys that do not answer or a code that keeps returning to the keypad, the ribbon, the relays or the main board, and replacing only the part that failed.
Shows up asWhat a Microwave Error Code Is Telling You
A microwave error code may be a letter and a number on the display, a lock or demo word, a row of dashes, or a beep with a blinking clock, and it can show while the microwave still heats or block every key until it is cleared.
MakeJennAir
JennAir microwaves looked at in place, with the breaker, the door switches and a one-minute heat test covered before any part is priced.
SourceJennAir Product Help, over-the-range microwave: F2
From JennAir's help pages for its microwave hood combinations (Euro-style, including the convection models). The code set varies with the control generation, so a code missing from your model's manual may not apply to it.
Before you book,
in this order.
Each step comes from JennAir's own guidance for F2 on its microwaves. Follow it to the end: the last card says whether this is a visit.
Turn the microwave off at the circuit breaker, count a full minute, then restore power.
Give it a minute on standby; a code that does not reappear was likely a one-time glitch, so run a short cycle to confirm.
Run the vent fan while cooking below so steam does not settle on the panel.
If F2 comes back, book a visit to have the keypad and its cable tested.
Still there?
It usually turns into microwave control board and touchpad repair. Book with the code and the model number.
What not to do
F2 is a panel code, not a sign the magnetron or the door has failed. If LOC or a padlock is lit, the panel is locked rather than broken.
What you may
notice with it.
The microwave problems F2 tends to arrive with. Answer these at the microwave before anyone is booked.
All problems
Where F2 usually leads
Microwave control board and touchpad repair.
JennAir
microwaves.
JennAir microwaves looked at in place, with the breaker, the door switches and a one-minute heat test covered before any part is priced.
JennAir microwave repairMore JennAir codes
All 21 JennAir codesControl board and touchpad on other makes
Microwave hood combination
The microwave that hangs from the wall cabinets above the burners, heating food in its cavity while its own fan, light and filters handle the steam and grease rising from the pans beneath it.
Built-in microwave
A microwave set into a tall cabinet or a wall of cabinetry at eye level, either a countertop body wrapped in a trim kit or a true built-in model, including speed and convection microwaves that brown as well as heat.
Microwave drawer
A microwave built under a counter or into a kitchen island that opens like a drawer at the touch of a key, with a motor and gears sliding its cavity out toward you.
In JennAir's own words
There may be a problem with the Keypad (User Interface) or the associated wiring.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. From JennAir's help pages for its microwave hood combinations (Euro-style, including the convection models). The code set varies with the control generation, so a code missing from your model's manual may not apply to it.
JennAir F2 microwave repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F2.
Can I clear F2 myself?
What is the usual repair for F2 on a JennAir?
Does F2 on a JennAir mean the same as E03?
Could boiling water below my JennAir trigger F2?
Back to your everyday
Still showing F2?
Three details make the booking useful: the characters or beeps just as they appeared, every character of the model number, and whether a cup of water still warms up. With those, the technician arrives already halfway to the answer.